The better route would have been to purchase lattice that had complete diamonds at each edge. When the two panels are put together side-by-side, they look like this:Īlthough I think the double diamond effect still looks good, I wanted the two panels to appear somewhat seamless. My lattice panels, however, were cut with partial edges. Ideally, the sheets of lattice would line up at the seam to create an uninterrupted span of little diamonds across both lattices. One thing I wish I had known before embarking on this project was to pay closer attention to how the lattice panels were cut back at the lattice-making factory. Repeat until all three lengths of strapping are affixed. Now that it’s level and straight, go ahead and drill in the rest of the screws along the length of the strapping. Use your level to determine the correct angle and then drill in a screw at the opposite end. Drill a screw into one end, but keep it loose. Place one length of strapping against the fence, 6 inches in from the stake. If it’s brick or concrete, simply space the strapping 12-inches down from top, 12-inches up from the bottom, with the last piece in between. If you’re installing the lattice trellis on vinyl siding, use the wall studs as your backstop. The fence here has three rails on the opposite side that are the perfect spot to drill into. I started by pre-drilling holes 2-inches from each end and spacing the rest approximately 20-inches apart.įind the best place to sink your screws on the wall. Step 3: Installing the Strappingĭrill pilot holes along each length of strapping. A circular saw makes the task quick and easy but a hand saw would also work. Placing the lattice face up (with the heads of the staples on top) will make sawing by hand go a bit more smoothly.īecause the strapping is to be 6-inches shorter than the lattice on each side, the lumber will need to be cut to 7-foot lengths. I used a keyhole saw to lower the chances of the slats cracking and breaking as they are cut. Wood lattice is a pretty flimsy material so take care when sawing. In my case, the fence is shorter than the panels so the height of each one will need to be cut to size. If your wall or fence is taller than 8 feet, you won’t need to cut your lattice pieces. Step 2: Cutting the Lumber to Your Measurements From each stake, measure 6-inches inward and mark these spots with a pencil. The strapping will be a bit shorter than the lattice panels on each side. Next, measure the height of the fence and then subtract an inch so the lattice won’t sit directly on the ground. I’ll be using two 4 foot wide lattice panels and orienting them vertically for an 8-foot long lattice.įigure out where you want to the lattice to be and drive two stakes into the ground to mark the position. The first thing to do is grab your measuring tape and mark out the placement of the lattice along your fence or wall. It’s a two-person job that takes an afternoon to put together, and only cost me about $50 in materials. With this bit of space, the twining plants can grow over and under the slats of lattice. The wood strips will make sure the structure is sturdy while also keeping the lattice 1.5 inches off the fence. The basic idea is to affix the lattice to the fence on top three horizontal lengths of strapping lumber. I’ve landed on a design that’s easy to make. The overly complex builds just wouldn’t do – and besides, this lattice will be covered in vining plants anyway. I didn’t want a freestanding trellis with concrete footings, or decorative add-ons like cap molding, or for the project to require specialized tools. Looking around the internet for tutorials that matched my vision had me coming up empty. I wanted the lattice trellis to look good and last a long time, but also be super simple to build. Not only should this do the trick and block encroaching weeds, it will create a beautiful living wall that I’ll enjoy for many years to come. My planty solution was to build a lattice trellis along the fence and grow some handsome climbing vines. So when vining weeds growing on my neighbor’s side of the fence kept poking through the panels, flowering, and scattering their seeds everywhere, I had to do something to stop the madness. Need privacy, better drainage, weed displacement, or to cover up an ugly view? Well, there’s a plant for that. I’m of the mind that there are few landscaping problems that more plants can’t solve.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |